Electronic Ignition Conversion Kit
for
Delco 4-cylinder, Non-Vacuum-Advance Distributors - 3DEL4U1
Delco 6-cylinder, Non-Vacuum-Advance Distributors - 3DEL6U1
Delco 4-cylinder, Vacuum-Advance Distributors - 3DEL4V1
Delco 6-cylinder, Vacuum-Advance Distributors - 3DEL6V1
Replaces Entire Breaker Plate - Simple to Install.
For aluminum-bodied Delco distributors only. NOT for older Delco cast-iron distributors.
The Hot-Spark 3DEL4U1 & 3DEL6U1 electronic ignition kits replace this entire Delco centrifugal-advance breaker plate:
Before ordering, please compare the points and breaker plate of your distributor to the photos of your breaker plate, points and distributor to make sure that this ignition kit is the right one for your distributor.
The HotSpark 3DEL4V1 and 3DEL6V1 ignition kits replace this entire Delco vacuum-advance breaker plate:
Measuring Coil Resistance (and more): www.Hot-Spark.com/Coil.htm
13.9 volts Maximum Charging System Voltage: Charging system voltage, measured at the coil's + terminal, must never exceed 13.9 volts at any RPM level. If voltage level exceeds 13.9 volts, a 1.4 Ohm ballast resistor must be wired between the coil's + terminal and the HotSpark red ignition wire. Otherwise, too much voltage/amperage can damage the ignition module.
www.Hot-Spark.com/Installing-Hot-Spark-Delco.pdf
International Buyers – Please Note:
Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility.
Please check with your country's customs office to determine what these additional costs will be prior to bidding/buying.
VERY IMPORTANT -- BEFORE ORDERING: Some distributors of vehicles, boats,
etc. may differ, according to whether the stock distributor is still in place or
a replacement distributor has been installed. Some otherwise similar or
identical engines use different distributor brands and/or different distributor
part numbers. We need your distributor's brand name, distributor part number and
number of engine cylinders to ensure that the electronic ignition conversion kit
is correct one for your particular distributor.
If your distributor part number, normally found on the side of the distributor
body, is not among those listed on the relevant web page, chances are, the
HotSpark ignition conversion kit won't fit your distributor.
It's imperative that we know your distributor's brand name, distributor part
number and the number of cylinders of your engine. You may need to remove the
distributor temporarily, so that you can read the distributor part number from
the side of the distributor body. Usually, the side of your distributor will be
covered with oil and dirt, so you'll need to clean it to find the distributor
brand name and exact part number.
We can guarantee only that each of our ignition kits will fit a distributor with
one of the distributor part numbers listed on its relevant web page. Otherwise,
it likely won't fit. HotSpark ignition kits require a 12-volt, negative ground
(earth) electrical system.
If you order the wrong electronic ignition conversion kit for your distributor,
you'll need to return it to us, via US Postal Service mail within 30 days from
date of purchase. If the ignition kit is in perfect, unused condition, we can
accept it as a retuned item, within 30 days of purchase, and provide a refund to
your PayPal account, less a 20% restocking fee and any international shipping
fees, etc., but only if the ignition kit is in pristine, unused condition. Buyer
is responsible for shipping and other costs to return the product for credit or
exchange.
Click on the photo of an electronic ignition conversion kit below for more detailed information:
|
Hot Spark Electronic Ignition Conversion Kit for 4-cylinder Delco non-vacuum-advance Distributors |
|||||||||||||
|
Easy to Install - Replace Entire Breaker Plate with Solid-State Electronics |
Electronic Ignition Conversion Kit. Replaces points and condenser in many 4-cylinder, Delco centrifugal-advance distributors.
|
||||||||||||
|
|||||||||||||
|
Electronic Ignition Conversion Kit for 4-cylinder Delco vacuum-advance Distributors |
|||||||||||||
|
Easy to Install - Replace Points and Condenser with Solid-State Electronics |
Electronic Ignition Conversion Kit. Replaces points and condenser in many 4-cylinder, Delco vacuum-advance distributors.
|
||||||||||||
|
|||||||||||||
|
Electronic Ignition Conversion Kit for 6-cylinder Delco non-vacuum-advance Distributors |
|||||||||||||
|
Easy to Install - Replace Points and Condenser with Solid-State Electronics |
Electronic Ignition Conversion Kit. Replaces points and condenser in many 6-cylinder, Delco centrifugal-advance distributors.
|
||||||||||||
|
|||||||||||||
|
Electronic Ignition Conversion Kit for 6-cylinder Delco vacuum-advance Distributors |
|||||||||||||
|
Easy to Install - Replace Points and Condenser with Solid-State Electronics |
Electronic Ignition Conversion Kit. Replaces points and condenser in many 6-cylinder, Delco vacuum-advance distributors.
|
||||||||||||
|
|||||||||||||
Foreign Orders: Shipping discount available if purchasing multiple items.
© 2005-2023 Hot Spark®
